5 Common Mistakes to Avoid When Putting in Customized Curtain Rods


Warning: Undefined variable $PostID in /home2/comelews/wr1te.com/wp-content/themes/adWhiteBullet/single.php on line 66

Warning: Undefined variable $PostID in /home2/comelews/wr1te.com/wp-content/themes/adWhiteBullet/single.php on line 67
RSS FeedArticles Category RSS Feed - Subscribe to the feed here
 

Installing customized curtain rods can elevate the look of any room, adding a touch of style and personalization. However, it’s not as simple as just drilling a few holes and hanging up your curtains. Small mistakes can lead to crooked rods, curtains that don’t grasp properly, and even damage to your walls. To save lots of yourself from frustration and further work, here are 5 frequent mistakes to keep away from when installing customized curtain rods.

1. Neglecting to Measure Properly

One of the biggest mistakes folks make is skipping the measurement step or doing it incorrectly. Curtain rods have to be positioned at a precise height and width to make sure the curtains look balanced and functional.

– Why It’s a Problem: If you happen to don’t measure accurately, your curtains may end up being too brief, too long, or not wide enough to cover the window.

– Find out how to Keep away from It: Use a tape measure to determine the height the place you need your rod to sit. Typically, rods should be installed four-6 inches above the window frame for a taller room appearance. Also, extend the rod 3-6 inches past the window frame on either side to permit for full curtain coverage and smooth opening.

2. Selecting the Flawed Hardware

Not all curtain rods and brackets are created equal. Deciding on the mistaken hardware can lead to instability or difficulty in hanging your curtains.

– Why It’s a Problem: Heavy curtains on flimsy rods can cause the rod to sag or even collapse. Equally, utilizing the fallacious type of screws or wall anchors can result in rods pulling out of the wall over time.

– The way to Avoid It: Check the load of your curtains and choose rods that can assist them. For heavy drapes, opt for sturdy rods with reinforced brackets. For those who’re installing into drywall, use appropriate anchors to ensure a secure hold.

3. Ignoring Wall Materials

Not all walls are the identical, and the type of wall you’re working with determines the set up approach and tools required.

– Why It’s a Problem: Failing to consider wall materials can lead to unstable installations. For example, nails or screws inserted directly into drywall without anchors will likely loosen over time.

– The best way to Avoid It: Determine whether your wall is drywall, plaster, concrete, or wood. For drywall, always use anchors. For concrete walls, you’ll want a masonry drill bit and anchors. Tailoring your approach to the wall materials ensures a secure and long-lasting installation.

4. Hanging the Rod Too Low

It’s tempting to install curtain rods just above the window frame, but this mistake can make your room look smaller and the window seem shorter.

– Why It’s a Problem: Curtains which can be hung too low can visually cut off the height of your room, making it feel cramped and less inviting.

– Methods to Keep away from It: Always aim to hang the curtain rod higher than the window frame—typically 4-6 inches above, and even closer to the ceiling for a dramatic effect. This trick draws the eye upward and makes your ceilings appear taller.

5. Forgetting to Level the Rod

A crooked curtain rod can spoil the overall aesthetic of your room, irrespective of how lovely the curtains are.

– Why It’s a Problem: Uneven rods make curtains dangle awkwardly, which is noticeable and unattractive.

– Methods to Avoid It: Always use a level before drilling or attaching brackets. Mark your measurements on the wall with a pencil and double-check for accuracy. Even a slight tilt can be discoverable, so take your time to ensure perfection.

Bonus Suggestions for a Flawless Curtain Rod Installation:

– Pre-Check Your Curtains: Earlier than putting in the rod, make positive the curtain size and style match your planned rod height and width.

– Use a Template: If putting in a number of rods, create a template to make sure uniform placement throughout the house.

– Consider Aesthetic: Match the rod style and end to your room’s decor for a cohesive look.

Putting in custom curtain rods doesn’t must be a hassle. By avoiding these widespread mistakes and following the ideas above, you’ll be able to achieve a cultured, professional-looking outcome that enhances your space. A little additional time spent on preparation and attention to element will save you from headaches down the road and give your windows the perfect frame they deserve.

When you loved this article and you would want to get more info concerning ironrods.com generously stop by our own page.

HTML Ready Article You Can Place On Your Site.
(do not remove any attribution to source or author)





Firefox users may have to use 'CTRL + C' to copy once highlighted.

Find more articles written by /home2/comelews/wr1te.com/wp-content/themes/adWhiteBullet/single.php on line 180