Write About Everything

Reasons Your fiat replacement key cost 500 Key Fob Won’t Work

A key fob for Fiat 500 allows you to easily open doors and start your vehicle. There are many reasons the fob may stop working. This could be due to a dead coin-battery or water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 remote key programming Flip Key Remote – an exact replica of the Ilco brand that needs to be professionally programmed by a local locksmith (click here for Locksmith Search). This remote includes trunk, Fiat 500 car key lock and unlock buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob that isn’t working. Modern key fobs have a limited range of operation and must be within only a few inches from the vehicle in order to function. If you’re far from your vehicle, and you push the keyfob button it will not respond and display the message “Key Fob Not Detected”.

If this happens, simply replace the battery in the coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them at your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing near your Fiat 500. The parking lights should flash and the key fob will operate the lock and unlock switch.

If your key fob still doesn’t work even after replacing the battery, there could be water damage that prevents it from communicating with the module in your vehicle. Water damage can occur in a variety of ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, you can place it in a rice bag to draw out the moisture. If this isn’t working, you’ll have to get your fob changed by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals that keep water from the chip’s electronic circuit and out of the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob’s circuit board which causes it to short out and eventually die. It’s not the best idea to soak the fob in water but don’t give up in the event that you accidentally drop it in the water or don’t take it out of your pocket.

Remove the battery first. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Next test the fob to verify if it is working. If the key doesn’t function then it might need to be changed. This is usually handled by an auto locksmith or dealer.

If your key is older and has not been programmed for your car You will need to replace it completely. A professional automotive locksmith can complete this simple process. The locksmith must cut the key to match the ignition on your vehicle. They’ll also need to reprogram the fob to the car’s system. This is a cheap and quick process that could be completed within the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob won’t be working is that it’s simply out of range. The remote usually has a range of 30 feet or less, and if it’s too far from your vehicle, it won’t respond to your commands. You can solve this problem by moving the remote closer to your vehicle until it responds.

If you’ve replaced your coin battery (commonly known as”button” or “button” or “watch”) and your fob doesn’t function, it could have an internal circuit board problem. Reprogramming the fob usually resolves this issue. You can find the instructions for the majority of vehicles on YouTube or in the owner’s guide.

It’s possible that you need to replace the metal clips that hold the coin battery. If they loose tension, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases, the fob may become desync’d with your vehicle due to software issues or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations they may have to reinstall the program in your body control module as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This can happen when the key fob is in proximity to an electronic radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob may not function because of a weak connection with the buttons, water damage or damage to the internal chips.

If the key fob been unable to function for a while in the middle of the night and you’ve tried everything you can at home to solve it e.g. replacing the battery, reprogramming it and using the spare key fob, you may have a defective receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

There is a simple way to reset the 500’s in-board system, 비회원 구매 including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer of your car. This could help you get your key fob working again. If the problem persists you should speak with an experienced technician. They will be able to identify the exact cause of any problems.